Development and Performance Evaluation of TiO₂–activated Carbon-based Air-purifying Paver Blocks for PM2.5 and VOC Removal
J. Environ. Nanotechnol., Volume 14, No 4 (December 2025) pp. 346-359
Abstract
Air pollution constitutes a major environmental crisis worldwide. Day-to-day, vehicles emit harmful air pollutants, posing various hazards to both living beings and the surrounding environment. The primary air pollutants responsible for health problems in urban areas are PM2.5 (particulate matter with an aerodynamic diameter of ≤ 2.5 µm) and volatile organic compounds (VOCs). Air-purifying paver blocks are used to significantly reduce air pollutants along pedestrian footpaths. The novelty of this research lies in the combined effect of titanium dioxide (TiO2) and geopolymer-based paver block production and the implementation of an Internet of Things (IoT) system to assess their effectiveness in reducing air pollution. The effectiveness of air-purifying paver blocks incorporated with TiO₂ and geopolymer concrete for the removal of PM2.5 and VOCs under field conditions was investigated. The results indicated that the paver blocks removed approximately 70% of PM2.5 and 50% of VOCs from the ambient air. In addition, the influence of operational parameters, such as temperature, humidity, and air velocity, on the performance of the paver blocks was examined. Data obtained from the IoT monitoring system revealed that CO and CO2 levels were lower at the centre of the paver blocks and gradually increased towards their outer edges. Owing to the combined advantages of TiO₂ and geopolymer-based paver blocks, their cost is approximately 5–10% higher than that of conventional fly-ash paver blocks; however, the associated environmental benefits are substantially greater.
Full Text
Reference
Ambient, National, Air Quality, and Monitoring Programme, Bulletin of Ambient Air Quality National Ambient Air Quality Monitoring Programme (NAMP)-Manual Monitoring System Central Pollution Control Board Ministry of Environment, Forests Climate Change, 1–44(2016).
Andrade, L. B., Rocha, J. C. and Cheriaf, M., Influence of Coal Bottom Ash as Fine Aggregate on Fresh Properties of Concrete, Constr. Build. Mater., 23(2), 609–14(2009).
https://doi.org/10.1016/j.conbuildmat.2008.05.003
Antoni., Klarens, K., Indranata, M., Jamali, L. A.and Hardjito, D., The Use of Bottom Ash for Replacing Fine Aggregate in Concrete Paving Blocks, MATEC Web Conf.erences., 138, 01005(2017).
https://doi.org/10.1051/matecconf/201713801005
Augustyniak, A., Jablonska, J., Cendrowski, K., Głowacka, K., Stephan, D., Mijowska, E.and Sikora, P., Investigating the Release of ZnO Nanoparticles from Cement Mortars on Microbiological Models, Appl. Nanosci., 12(3), 489–502(2022).
https://doi.org/10.1007/s13204-021-01695-w
Awadalla, A., Zain, M. F. M., Kadhum, A. A. H.and Abdalla, Z., Titanium Dioxide as Photocatalyses to Create Self Cleaning Concrete and Improve Indoor Air Quality, Int. J. Phys. Sci., 6(29), 6767–6774(2011).
https://doi.org/10.5897/IJPS11.254
Bica, B. O. and Melo, J. V. S. D., Concrete Blocks Nano-Modified with Zinc Oxide (ZnO) for Photocatalytic Paving: Performance Comparison with Titanium Dioxide (TiO2), Constr. Build. Mater., 252, 119120(2020).
https://doi.org/10.1016/j.conbuildmat.2020.119120
Binag, N. D., Powdered Shell Wastes as Partial Substitute for Masonry Cement Mortar in Binder, Tiles and Bricks Production, Int. J. Eng. Res. Technol. (IJERT)., 5(7), 70–77(2016).
Boonen, E. and Beeldens, A., Recent Photocatalytic Applications for Air Purification in Belgium, Coat., 4(3), 553–73(2014).
https://doi.org/10.3390/coatings4030553
Bruno, M. E., Tasat, D. R., Ramos, E., Paparella, M. L., Evelson, P., Rebagliati, R. J., Cabrini, R. L., Guglielmotti, M. B. and Olmedo, D. G., Impact through time of different sized titanium dioxide particles on biochemical and histopathological parameters, J. Biomed. Mater. Res. Part A., 102, 1439–1448(2014).
https://doi.org/10.1002/jbm.a.34822
Chu, S. H., Poon, C. S., Lam, C. S. and Li, L., Effect of Natural and Recycled Aggregate Packing on Properties of Concrete Blocks, Constr. Build. Mater., 278, 122247(2021).
https://doi.org/10.1016/j.conbuildmat.2021.122247
CPCB., “National Air Quality Index.” Central Pollution Control Board (CPCB), no. January, 1–44(2014).
Fan, L. F., Wu, Z. J., Wan, Z. and Gao, J. W., Experimental Investigation of Thermal Effects on Dynamic Behavior of Granite, Appl. Therm. Eng., 125, 94–103(2017).
https://doi.org/10.1016/j.applthermaleng.2017.07.007
García, C. M., Fonteboa, B. G., Abella, F. M.and López, D. C., Performance of Mussel Shell as Aggregate in Plain Concrete, Constr. Build. Mater., 139, 570–583(2017).
https://doi.org/10.1016/j.conbuildmat.2016.09.091
Gauvin, F., Caprai, V., Yu, Q. L.and Brouwers, H. J. H., Effect of the Morphology and Pore Structure of Porous Building Materials on Photocatalytic Oxidation of Air Pollutants, Appl. Catal. B., 227, 123–31(2018).
https://doi.org/10.1016/j.apcatb.2018.01.029
Glenn, G. M., Gray, G. M., Orts, W. J.and Wood, D. W., Starch-Based Lightweight Concrete: Effect of Starch Source, Processing Method, and Aggregate Geometry, Ind. Crops Prod., 9(2), 133–44(1999).
https://doi.org/10.1016/S0926-6690(98)00024-7
Gopalan, A. I., Lee, J. C., Saianand, G., Lee, K. P., Sonar, P., Dharmarajan, R., Hou, Y. L., Ann, K. Y., Kannan, V. and Kim, W. J., Recent Progress in the Abatement of Hazardous Pollutants Using Photocatalytic TiO2-Based Building Materials, Nanomater., 10(9), 1854(2020).
https://doi.org/10.3390/nano10091854
Hamad, B. S., Rteil, A. A. and Fadel, M. E., Effect of Used Engine Oil on Properties of Fresh and Hardened Concrete, Constr. Build. Mater., 17(5), 311–318(2003).
https://doi.org/10.1016/S0950-0618(03)00002-3
Hassan, M. M., Dylla, H., Mohammad, L. N.and Rupnow, T., Evaluation of the Durability of Titanium Dioxide Photocatalyst Coating for Concrete Pavement, Constr. Build. Mater., 24(8), 1456–61(2010).
https://doi.org/10.1016/j.conbuildmat.2010.01.009
Hopewell, J., Dvorak, R. and Kosior., Plastics Recycling: Challenges and Opportunities, Phil. Trans. R. Soc. B., 364(1526), 2115–2126(2009).
https://doi.org/10.1098/rstb.2008.0311
Hüsken, G., Hunger, M. and Brouwers, H. J. H., Experimental Study of Photocatalytic Concrete Products for Air Purification, Build. Environ., 44(12), 2463–2474(2009).
https://doi.org/10.1016/j.buildenv.2009.04.010
IS:15658-2006, Indian Standard Precast Concrete Block for Paving-Specification, Bureau of Indian Standards, 1–27(2006).
Ke, G., Li, W., Li, R., Li, Y. and Wang, G., Mitigation Effect of Waste Glass Powders on Alkali–Silica Reaction (ASR) Expansion in Cementitious Composite, Int. J. Concr. Struct. Mater., 12(1), 67(2018).
https://doi.org/10.1186/s40069-018-0299-7
Kim, H. J., Yoon, Y. S., Yang, K. H. and Kwon, S. J., Durability and Purification Performance of Concrete Impregnated with Silicate and Sprayed with Photocatalytic TiO2, Constr. Build. Mater., 199, 106–114(2019).
https://doi.org/10.1016/j.conbuildmat.2018.12.035
Kumar, G., Shrivastava, S. and Gupta, R. C., Paver Blocks Manufactured from Construction & Demolition Waste, Mater. Today. Proc., 27, 311–317(2020).
https://doi.org/10.1016/j.matpr.2019.11.039
Manivel, P. and Aarthi, K., Experimental Study on Concrete with Replacement of Coarse Aggregate by Using Granite Waste, IJARIIE., 6(2), 710–718(2020).
Melo, J. V. S. D., Trichês, G., Gleize, P. J. P.and Villena, J., Development and Evaluation of the Efficiency of Photocatalytic Pavement Blocks in the Laboratory and after One Year in the Field, Constr. Build. Mater., 37, 310–319(2012).
https://doi.org/10.1016/j.conbuildmat.2012.07.073
Mikhaylov, R. V., Lisachenko, A. A., Shelimov, B. N., Kazansky, V. B., Martra, G., Alberto, G.and Coluccia, S., FTIR and TPD Analysis of Surface Species on a TiO 2 Photocatalyst Exposed to NO, CO, and NO−CO Mixtures: Effect of UV−Vis Light Irradiation, J. Phys. Chem. C., 113(47), 20381–20387(2009).
https://doi.org/10.1021/jp906176c
Padmini, A. K., Ramamurthy, K. and Mathews, M. S., Influence of Parent Concrete on the Properties of Recycled Aggregate Concrete, Constr. Build. Mater., 23(2), 829–836(2009).
https://doi.org/10.1016/j.conbuildmat.2008.03.006
Poon, C. S. and Cheung, E., NO Removal Efficiency of Photocatalytic Paving Blocks Prepared with Recycled Materials, Constr. Build. Mater., 21(8), 1746–1753(2007).
https://doi.org/10.1016/j.conbuildmat.2006.05.018
Ramirez, A. M., Demeestere, K., Belie, N. D., Mäntylä, T. and Levänen, E., Titanium Dioxide Coated Cementitious Materials for Air Purifying Purposes: Preparation, Characterization and Toluene Removal Potential, Build. Environ., 45(4), 832–838(2010).
https://doi.org/10.1016/j.buildenv.2009.09.003
Raza, A., Azab, M., Baki, Z. A., Hachem, C. E.,Ouni, M. H. E. and Kahla, N. B., Experimental Study on Mechanical, Toughness and Microstructural Characteristics of Micro-Carbon Fibre-Reinforced Geopolymer Having Nano TiO2, Alexandria Eng. J., 64, 451–463(2023).
https://doi.org/10.1016/j.aej.2022.09.001
Reshma, T. V., Manjunatha, M., Bharath, A.,Tangadagi, R. B., Vengala, J. and Manjunatha, L., Influence of ZnO and TiO2 on Mechanical and Durability Properties of Concrete Prepared with and without Polypropylene Fibers, Mater., 18, 101138(2021).
https://doi.org/10.1016/j.mtla.2021.101138
Rhee, I., Lee, J. S., Kim, J. B. and Kim, J. H., Nitrogen Oxides Mitigation Efficiency of Cementitious Materials Incorporated with TiO2, Mater., 11(6), 877(2018).
https://doi.org/10.3390/ma11060877
Rosso, L. T. D. and Melo, V. S. D. M., Impact of Incorporating Recycled Glass on the Photocatalytic Capacity of Paving Concrete Blocks, Constr. Build. Mater., 259, 119778(2020).
https://doi.org/10.1016/j.conbuildmat.2020.119778
Sandrine, U. B., Isabelle, V., Hoang, M. T.and Chadi, M., Influence of Chemical Modification on Hemp–Starch Concrete, Constr. Build. Mater., 81 208–215(2015).
https://doi.org/10.1016/j.conbuildmat.2015.02.045
Singh, M. and Siddique, R., Properties of Concrete Containing High Volumes of Coal Bottom Ash as Fine Aggregate, J. Cleaner Prod., 91, 269–278(2015).
https://doi.org/10.1016/j.jclepro.2014.12.026
Sorathiya, J., Shah, S. and Kacha, S., Effect on Addition of Nano "Titanium Dioxide” (TiO2) on Compressive Strength of Cementitious Concrete, Int. conf. res. Innovations. Sci. eng. Technol., 219–211(2017).
Verbruggen, S. W., Ribbens, S., Tytgat, T., Hauchecorne, B., Smits, M., Meynen, V., Cool, P., Martens, J. A. and Lenaerts, S., The Benefit of Glass Bead Supports for Efficient Gas Phase Photocatalysis: Case Study of a Commercial and a Synthesised Photocatalyst, Chem. Eng. J., 174 (1), 318–325(2011).
https://doi.org/10.1016/j.cej.2011.09.038
Witkowski, H., Rek, W. J., Chilmon, K.,Jarosławski, J., Bojarska, A. T. and Gąsiński, A., Air Purification Performance of Photocatalytic Concrete Paving Blocks after Seven Years of Service, Appl. Sci., 9(9), 1735(2019).
https://doi.org/10.3390/app9091735
Yu, H., Dai, W., Qian, G., Gong, X., Zhou, D., Li, X. and Zhou, X., The NOx Degradation Performance of Nano-TiO2 Coating for Asphalt Pavement, Nanomater., 10(5), 897(2020).
