Strength and Durability Enhancement in Geopolymer Mortar Incorporating Nano-silica and Nano-GGBFS
J. Environ. Nanotechnol., Volume 14, No 3 (September 2025) pp. 495-504
Abstract
The construction sector is facing an increasing number of challenges due to the substantial carbon footprint associated with cement production, which significantly contributes to global CO₂ emissions. Geopolymer compounds are emerging as a sustainable alternative, as they reduce the necessity for cement while achieving comparable or better performance. Recent developments in the incorporation of nanomaterials into cementitious systems have demonstrated substantial improvements in microstructural densification, durability, and strength. Nanoparticles, such as nano silica (NS) and nano-GGBFS (N-GGBFS), accelerate geopolymerization, optimize pore structure, and improve the interfacial transition zone, resulting in improved mechanical and durability properties. The present research explores geopolymer mortar (GPM) and analyzes the influence of nanomaterials on its fresh and hardened properties. The inclusion of nanoparticles not only accelerated early strength development but also enhanced long-term performance by diminishing porosity and bolstering resilience to environmental degradation. The results indicate that nanomodified geopolymer mortar is a feasible, environmentally sustainable option for construction, aiding in the decrease of greenhouse gas emissions while upholding superior performance standards.
Full Text
Reference
Adak, D., Sarkar, M., and Mandal, S., Structural performance of nano-silica modified fly-ash based geopolymer concrete, Constr. Build. Mater., 135, 430–439(2017).
https://doi.org/10.1016/j.conbuildmat.2016.12.111
Ahmed, H. U., Mohammed, A. S., Faraj, R. H., Qaidi, S. M. A., and Mohammed, A. A., Compressive strength of geopolymer concrete modified with nano-silica: Experimental and modeling investigations, Case Stud. Constr. Mater., 16, e01036(2022).
https://doi.org/10.1016/j.cscm.2022.e01036.
Althoey, F., Ansari, W. S., Sufian, M., and Deifalla, A. F. Advancements in low-carbon concrete as a construction material for the sustainable built environment. Dev. Built Environ., 16, 100284(2023).
https://doi.org/10.1016/j.dibe.2023.100284.
ASTM C109/C109M-24 – Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 50-mm Cube Specimens). ASTM International, West Conshohocken, PA.
ASTM C1585-24 – Standard Test Method for Measurement of Rate of Absorption of Water by Hydraulic-Cement Concretes. ASTM International, West Conshohocken, PA.
ASTM C642 – Standard Test Method for Density, Absorption, and Voids in Hardened Concrete. ASTM International, West Conshohocken, PA.
ASTM C882 / C882M – Standard Test Method for Bond Strength of Epoxy-Resin Systems Used with Concrete by Slant Shear. ASTM International, West Conshohocken, PA.
Barbhuiya, S., Kanavaris, F., Das, B. B. and Idrees, M., Decarbonising cement and concrete production: Strategies, challenges and pathways for sustainable development, J. Build. Eng., 86, 108861(2024).
https://doi.org/10.1016/j.jobe.2024.108861
Çevik, A., Alzeebaree, R., Humur, G., Niş, A. and Gülşan, M. E., Effect of nano-silica on the chemical durability and mechanical performance of fly ash based geopolymer concrete, Ceram. Int., 44(11), 12253–12264(2018).
https://doi.org/10.1016/j.ceramint.2018.04.009.
Chithra, S., Kumar, S. R. R. S. and Chinnaraju, K., The effect of colloidal nano-silica on workability, mechanical and durability properties of high performance concrete with copper slag as partial fine aggregate, Constr. Build. Mater., 113, 794–804(2016).
https://doi.org/10.1016/j.conbuildmat.2016.03.119.
Cong, P. and Cheng, Y., Advances in geopolymer materials: A comprehensive review, J. Traffic Transp. Eng., 8(3), 283–314(2021).
https://doi.org/10.1016/j.jtte.2021.03.004
Deb, P. S., Kuri, J. C. and Sarker, P., Nano-modified geopolymer and alkali-activated systems, Elsevier., 347-374(2022).
https://doi.org/10.1016/B978-0-323-85229-6.00001-9
Deb, P. S., Sarker, P. K. and Barbhuiya, S., Sorptivity and acid resistance of ambient-cured geopolymer mortars containing nano-silica, Cem. Concr. Compos., 72, 235–245(2016).
https://doi.org/10.1016/j.cemconcomp.2016.06.017.
Fallah, S. and Nematzadeh, M., Mechanical properties and durability of high-strength concrete containing macro-polymeric and polypropylene fibers with nano-silica and silica fume, Constr. Build. Mater., 132, 170-187(2017).
https://doi.org/10.1016/j.conbuildmat.2016.11.100
Gao, X., Yu, Q. L. and Brouwers, H. J. H., Characterization of alkali activated slag–fly ash blends containing nano-silica, Constr. Build. Mater., 98, 397–406(2015).
https://doi.org/10.1016/j.conbuildmat.2015.08.086.
Ige, O. E., Kallon, D. V. V. and Desai, D., Carbon emissions mitigation methods for cement industry using a systems dynamics model, Clean Technol. Environ. Policy., 26(3), 579–597(2024).
https://doi.org/10.1007/s10098-023-02683-0.
IS 2250:1981 – Code of practice for preparation and use of masonry mortars.
IS 383:2016 – Specification for Coarse and Fine Aggregates for Concrete.
IS 4031 (Part 6):1988 – Methods of physical tests for hydraulic cement, Part 6: Determination of compressive strength of hydraulic cement (other than masonry cement).
Jaishankar, P., Poovizhi, K. and Mohan, K., Strength and durability behaviour of nano silica on high performance concrete, Int. J. Eng. Technol., 7(3.12), 415(2018).
https://doi.org/10.14419/ijet.v7i3.12.16118
Kavitha, E., Revathi, S., Reena, L. and Vinodhini, C., Influence of Nano-SiO₂ and Nano-TiO₂ on self-compacting concrete: A study of rheology and strength improvement, J. Environ. Nanotechnol., 13(4), 161–168(2024).
https://doi.org/10.13074/jent.2024.12.2441074.
Khaiyum, M. Z., Sarker, S. and Kabir, G., Evaluation of carbon emission factors in the cement industry: An emerging economy context, Sustainability., 15(21), 15407(2023).
https://doi.org/10.3390/su152115407.
Khater, H. M., Effect of nano-silica on microstructure formation of low-cost geopolymer binder, Nanocomposites., 2(2), 84–97(2016).
https://doi.org/10.1080/20550324.2016.1203515.
Li, M., Sun, J., Li, L., Meng, L., Wang, S., Wei, J. and Mao, J. Effect of nanosilica on fiber pullout behavior and mechanical properties of strain hardening ultra-high performance concrete, Constr. Build. Mater., 367, 130255 (2023).
https://doi.org/10.1016/j.conbuildmat.2022.130255.
Lo, K. W., Lin, K. L., Cheng, T. W., Chang, Y. M. and Lan, J. Y., Effect of nano-SiO2 on the alkali-activated characteristics of spent catalyst metakaolin-based geopolymers, Constr. Build. Mater., 143, 455–463(2017).
https://doi.org/10.1016/j.conbuildmat.2017.03.152.
Madirisha, M. M., Dada, O.R. and Ikotun, B. D., Chemical fundamentals of geopolymers in sustainable construction, Mater. Today Sustainability., 27, 100842(2024).
https://doi.org/10.1016/j.mtsust.2024.100842.
Marathe, S. and Sadowski, Ł., Developments in biochar incorporated geopolymers and alkali activated materials: A systematic literature review, J. Clean Prod., 469, 143136(2024).
https://doi.org/10.1016/j.jclepro.2024.143136
Mukharjee, B. B. and Barai, S., Influence of incorporation of colloidal nano-silica on behaviour of concrete, Iran. J. Sci. Technol. Trans. Civ. Eng., 44(2), 657-668(2020).
https://doi.org/10.1007/s40996-020-00382-0
Mulapeer, E. M. and Omar, A. H., Durability and mechanical performance of geopolymer mortar with partial replacement of fly ash by rice husk ash and variations in alkaline activator concentrations, Discover. Civ. Eng., 2(1), 82(2025).
https://doi.org/10.1007/s44290-025-00234-8.
Nikolakopoulos, A., Steriotis, T., Charalambopoulou, G., Karagiannakis, G., Dimitrakis, D., Michalis, V. and Katsiotis, M., Reducing carbon emissions in cement production through solarization of the calcination process and thermochemical energy storage, Comput. Chem. Eng., 180, 108506 (2024).
https://doi.org/10.1016/j.compchemeng.2023.108506
Nilimaa, J., Smart materials and technologies for sustainable concrete construction, Dev. Built Environ., 15, 100177(2023).
https://doi.org/10.1016/j.dibe.2023.100177.
Perera, M. and Ranjith, P., Eco-friendly cementitious composites for enhanced strength: Emerging trends and innovations, J. Clean Prod., 468, 142962(2024).
https://doi.org/10.1016/j.jclepro.2024.142962
Phoo-ngernkham, T., Chindaprasirt, P., Sata, V., Hanjitsuwan, S. and Hatanaka, S., The effect of adding nano-SiO2 and nano-Al2O3 on properties of high calcium fly ash geopolymer cured at ambient temperature, Mater. Des., 55, 58–65(2014).
https://doi.org/10.1016/j.matdes.2013.09.049.
Raj, R. S., Arulraj, G. P., Anand, N., Kanagaraj, B., Lubloy, E. and Naser, M. Z., Nanomaterials in geopolymer composites: A review, Dev. Built Environ., 13, 100114(2023).
https://doi.org/10.1016/j.dibe.2022.100114
Rashad, A. M., Effect of nanoparticles on the properties of geopolymer materials, Mag. Concr. Res., 71(24), 1283–1301(2019).
https://doi.org/10.1680/jmacr.18.00289
Regalla, S. S. and Kumar, S., The enhancing role of nanomaterials in revolutionizing ultra-high-performance concrete (UHPC): A journey from atomic precision to structural prominence, Case Stud. Constr. Mater., 22, e04608(2025).
https://doi.org/10.1016/j.cscm.2025.e04608.
Ridha, S. and Yerikania, U., The strength compatibility of nano-SiO2 geopolymer cement for oil well under HPHT conditions, J. Civ. Eng. Res., 6–10(2015).
https://doi.org/10.5923/c.jce.201501.02.
Rodríguez, E. D., Bernal, S. A., Provis, J. L., Paya, J., Monzo, J. M. and Borrachero, M. V., Effect of nanosilica-based activators on the performance of an alkali-activated fly ash binder, Cem. Concr. Compos., 35(1), 1–11(2013).
https://doi.org/10.1016/j.cemconcomp.2012.08.025.
Roy, R., Mitra, A., Ganesh, A. T. and Sairam, V., Effect of graphene oxide nanosheets dispersion in cement mortar composites incorporating metakaolin and silica fume, Constr. Build. Mater., 186, 514–524(2018).
https://doi.org/10.1016/j.conbuildmat.2018.07.135.
Said, Z., Pandey, A. K., Tiwari, A. K., Kalidasan, B., Jamil, F., Thakur, A. K., Tyagi, V. V., Sarı, A. and Ali, H. M., Nano-enhanced phase change materials: Fundamentals and applications, Prog. Energy Combust. Sci., 104, 101162(2024).
https://doi.org/10.1016/j.pecs.2024.101162.
Si, W., Khan, M. and McNally, C., Effect of nano silica with high replacement of GGBS on enhancing mechanical properties and rheology of 3D printed concrete, Results Eng.,27, 106680(2025).
https://doi.org/10.1016/j.rineng.2025.106680.
Singh, N. B. and Middendorf, B., Geopolymers as an alternative to Portland cement: An overview, Constr. Build. Mater., 237, 117455(2020).
https://doi.org/10.1016/j.conbuildmat.2019.117455.
Srikanth, S., Krishna, C. B. R., Srikanth, T., Nitesh, K. J. N. S., Nadh, V. S., Kumar, S. and Thanappan, S., Effect of nano ground granulated blast furnace slag (GGBS) volume % on mechanical behaviour of high-performance sustainable concrete, J. Nanomater., 2022(1), 3742194(2022).
https://doi.org/10.1155/2022/3742194.
Wang, J., Du, P., Zhou, Z., Xu, D., Xie, N. and Cheng, X., Effect of nano-silica on hydration, microstructure of alkali-activated slag, Constr. Build. Mater., 220, 110–118(2019).
https://doi.org/10.1016/j.conbuildmat.2019.05.158.
Yang, F., Yao, Y., Wei, J., Wang, X. and Feng, Z., Estimating the effect of vibration mixing process on air pore size distributions in concrete using digital image analysis, Build., 12(8), 1142(2022).
https://doi.org/10.3390/buildings12081142
Yang, L. Y., Jia, Z. J., Zhang, Y. M. and Dai, J. G., Effects of nano-TiO2 on strength, shrinkage and microstructure of alkali activated slag pastes, Cem. Concr. Compos., 57, 1–7(2015).
https://doi.org/10.1016/j.cemconcomp.2014.11.009
Yildirim, G., Sahmaran, M. and Ahmed, H. U., Influence of hydrated lime addition on the self-healing capability of high-volume fly ash incorporated cementitious composites, J. Mater. Civ. Eng., 27(6), 04014187(2015).
https://doi.org/10.1061/(ASCE)MT.1943-5533.0001145.
Zhang, P., Gao, Z., Wang, J., Guo, J., Hu, S. and Ling, Y., Properties of fresh and hardened fly ash/slag based geopolymer concrete: A review, J. Clean. Prod., 270, 122389(2020).
https://doi.org/10.1016/j.jclepro.2020.122389
Zhang, P., Li, Q., Wang, J., Shi, Y. and Ling, Y., Effect of PVA fiber on durability of cementitious composite containing nano-SiO2, Nanotechnol. Rev., 8(1), 116–127(2019).
