Open Access

Dynamic Analysis of Laminated Composite with Inclusion

A. Usha Bharathi, Usha.aero@kcgcollege.com
Department of Aeronautical Engineering, KCG College of Technology, Karapakkam, Chennai, TN, India
P. Irin Maria, Department of Aeronautical Engineering, KCG College of Technology, Karapakkam, Chennai, TN, India S. Maithreyi , Department of Aeronautical Engineering, KCG College of Technology, Karapakkam, Chennai, TN, India N. Soorya Sree Department of Aeronautical Engineering, KCG College of Technology, Karapakkam, Chennai, TN, India


J. Environ. Nanotechnol., Volume 13, No 3 (2024) pp. 392-399

https://doi.org/10.13074/jent.2024.09.242662

PDF


Abstract

With growing environmental awareness, ecological concerns and new legislations, bio-fibre reinforced polymer composites have received increasing attention during the recent decades. This study focuses on the processing of seashell powder into micron size and utilizing the same as filler with glass fibres and epoxy resin in the preparation of the composite, thereby increasing mechanical strength. The constituents used in this composite showcase properties like higher strength, higher stiffness, chemical resistance, good insulation to electricity and lightweight. The components found in seashell such as Na, Ca, Al and C along with the S-glass fibre and the binding provided by the resin are responsible for enhancing hardness and tensile strength of the composite. Numerical analysis for the tensile test was done using ANSYS simulation for both composites with 5% filler (50% fibre + 45% resin+ 5% seashell) and without filler (50% fibre + 50% resin). Two laminate composites, with 5% filler (50% fibre + 45% resin+ 5% seashell) and without filler (50% fibre + 50% resin) were fabricated and their mechanical properties were compared using various tests like tensile and low velocity impact test with an impact velocity of 1 m/s, 2 m/s, 3 m/s and 4 m/s. The results from these tests were interpreted. The findings show that the specimen with 5% filler has more ultimate strength and impact strength when compared to the one without filler.

Full Text

Reference


Andersons, J., Joffe, R., Hojo, M. and Ochiai, S., Glass fibre strength distribution determined by common experimental methods, Compos. Sci. Technol., 62 (1), 131–145 (2002).

https://doi.org/10.1016/S0266-3538(01)00182-8

Azarian, M. H. and Sutapun, W., Biogenic calcium carbonate derived from waste shells for advanced material applications: A review, Front. Mater., 9 1024977 (2022).

https://doi.org/10.3389/fmats.2022.1024977

Dhanaraj, K. and Suresh, G., Conversion of waste sea shell ( Anadara granosa ) into valuable nanohydroxyapatite (nHAp) for biomedical applications, Vacuum, 152 222–230 (2018).

https://doi.org/10.1016/j.vacuum.2018.03.021

Dickson, A. N., Barry, J. N., McDonnell, K. A. and Dowling, D.P., Fabrication of continuous carbon, glass and Kevlar fibre reinforced polymer composites using additive manufacturing, Addit. Manuf., 16 146–152 (2017).

https://doi.org/10.1016/j.addma.2017.06.004

Ferreira, J. A. M., Costa, J. D. M., Reis, P. N. B. and Richardson, M. O. W., Analysis of fatigue and damage in glass-fibre-reinforced polypropylene composite materials, Compos. Sci. Technol., 59 (10), 1461–1467 (1999).

https://doi.org/10.1016/S0266-3538(98)00185-7

Gopal, K. U. B., Srinivasa, C. S., Amara, N. S. and Gudoor, S., Processing, characterization and property evaluation of seashell and glass fibre added epoxy based polymer matrix composite, Mater. Today Proc., 35 417–422 (2021).

https://doi.org/10.1016/j.matpr.2020.02.818

Hosseini, A. and Raji, A., Enhancement of high-performance structures with sustainable seashell filler-based GFRP composites in static loading, Mater. Res. Express, 10 (6), 065301 (2023).

https://doi.org/10.1088/2053-1591/acd910

Koçhan, C., Mechanical properties of waste mussel shell particles reinforced epoxy composites, Mater. Test, 61 (2), 149–154 (2019).

https://doi.org/10.3139/120.111298

Lee, N. J. and Jang, J., The effect of fibre content on the mechanical properties of glass fibre mat/polypropylene composites, Compos. Part Appl. Sci. Manuf., 30 (6), 815–822 (1999).

https://doi.org/10.1016/S1359-835X(98)00185-7

Moustafa, H., Youssef, A. M., Duquesne, S. and Darwish, Nabila.A., Characterization of bio‐filler derived from seashell wastes and its effect on the mechanical, thermal, and flame retardant properties of ABS composites, Polym. Compos., 38 (12), 2788–2797 (2017).

https://doi.org/10.1002/pc.23878

Nanda Kishore, A., Malhotra, S. K. and Siva, P. N., Failure analysis of multi-pin joints in glass fibre/epoxy composite laminates, Compos. Struct., 91 (3), 266–277 (2009).

https://doi.org/10.1016/j.compstruct.2009.04.043

Norazlina, H., Fahmi, A. R. M. and Hafizuddin, W. M. CaCO3 from seashells as a reinforcing filler for natural rubber, J. Mech. Eng. Sci., 8 1481–1488 (2015).

https://doi.org/10.15282/jmes.8.2015.22.0144

Owuamanam, S. and Cree, D., Progress of Bio-Calcium Carbonate Waste Eggshell and Seashell Fillers in Polymer Composites: A Review, J. Compos. Sci., 4 (2), 70 (2020).

https://doi.org/10.3390/jcs4020070

Ravi, S. H., Srikant, R. R., Vamsi, K. P., Bhujanga, R. V. and Bangaru, B. P., Estimation of the Dynamic Properties of Epoxy Glass Fabric Composites with Natural Rubber Particle Inclusions, Int. J. Automot. Mech. Eng., 7 968–980 (2013).

https://doi.org/10.15282/ijame.7.2012.13.0078

Salawu, M. A., Ayinla, I. K., Salahudeen, M. A., Adeoye, J. A., Jegede, P. T., Ezike, S. C., Olasanmi, O. O., Omoniyi, F. O. and Alabi, A. B., Characterizations of some discarded shells particles polymer-based composites for ceilings and particles board applications, Recent. Adv. Nat. Sci., 17 (2023).

https://doi.org/10.61298/rans.2023.1.2.17

Sanjay, M. R., Arpitha, G. R. and Yogesha, B., Study on Mechanical Properties of Natural - Glass Fibre Reinforced Polymer Hybrid Composites: A Review, Mater. Today Proc., 2 (4–5), 2959–2967 (2015).

https://doi.org/10.1016/j.matpr.2015.07.264

Santulli, C., Fragassa, C., Pavlovic, A. and Nikolic, D., Use of Sea Waste to Enhance Sustainability in Composite Materials: A Review, J. Mar. Sci. Eng., 11 (4), 855 (2023).

https://doi.org/10.3390/jmse11040855

Satyanarayana, K. G., Sukumaran, K., Kulkarni, A. G., Pillai, S. G. K. and Rohatgi, P. K., Fabrication and properties of natural fibre-reinforced polyester composites, Composites, 17 (4), 329–333 (1986).

https://doi.org/10.1016/0010-4361(86)90750-0

Seshavenkat, N. B. and Krovvidi, S., Fabrication of E-Glass Fibre Based Composite Material with Induced Particulate Additives, IOP Conf. Ser. Mater. Sci. Eng., 1033 (1), 012075 (2021).

https://doi.org/10.1088/1757-899X/1033/1/012075

Shettigar, Y. P., Obed D’Souza, R., Jose, A., Gopinath, A., Prakashan, D. and Rajeev, V., Fabrication and testing of Fibre-reinforced Glass-epoxy composite with Seashell as a filler Material, IOP Conf. Ser. Mater. Sci. Eng., 376 012066 (2018).

https://doi.org/10.1088/1757-899X/376/1/012066

Stanciu, M. D., Drăghicescu, H. T. and Roșca, I. C., Mechanical Properties of GFRPs Exposed to Tensile, Compression and Tensile–Tensile Cyclic Tests, Polymers, 13 (6), 898 (2021).

https://doi.org/10.3390/polym13060898

Varga, C. S., Miskolczi, N., Bartha, L. and Lipóczi, G., Improving the mechanical properties of glass-fibre-reinforced polyester composites by modification of fibre surface, Mater. Des., 31 (1), 185–193 (2010).

https://doi.org/10.1016/j.matdes.2009.06.034

Yarlagaddaa, J. and Ramakrishna, M., Fabrication and characterization of S glass hybrid composites for Tie rods of aircraft, Mater. Today Proc., 19 2622–2626 (2019).

https://doi.org/10.1016/j.matpr.2019.10.104

Žmak, I., Ćorić, D., Surjak, M. and Žalac, E., Properties of biocomposites from waste seashells and poly(methyl methacrylate): Eigenschaften von Bioverbundwerkstoffen aus Muschelabfällen und Polymethylmethacrylat, Mater. Werkst., 48 (8), 779–784 (2017).

https://doi.org/10.1002/mawe.201700022

Contact Us

Powered by

Powered by OJS