Open Access

Studies on the Fabrication of Surface Composites on Cast Aluminum Alloys using Friction Stir Processing - A Review

K.Periasamy , rk.periyasamy@gmail.com
Department of Mechanical Engineering, Kongunadu College of Engineering and Technology, Thottiyam, TN, India.
M. Jayaraman Department of Mechanical Engineering, Vellalar College of Engineering and Technology, Erode, TN, India.


J. Environ. Nanotechnol., Volume 5, No 1 (2016) pp. 46-51

https://doi.org/10.13074/jent.2016.03.161178

PDF


Abstract

Aluminum and its alloys are used extensively in aerospace and automotive industries because of its low density and high strength to weight ratio. Metal matrix composites are a new class of materials that exhibit good wear and erosion resistance properties, higher stiffness and hardness at a lower density as compared to the matrix. However, the presence of the ceramic particles in the metallic matrix makes the matrix brittle Hence, instead of bulk reinforcement, if the ceramic particles would be added to the surface, it could improve the wear and erosion resistance without sacrificing the bulk properties. Dispersion of ceramic particles on metallic substrate surface and the control of its distribution are difficult to achieve by conventional surface treatments. Recently, much attention has been paid to a new surface modification technique named friction stir processing.FSP is a solid state processing technique to obtain a fine-grained microstructure. It is well known that the stirred zone consists of fine and equiaxed grains produced due to dynamic recrystallization. Though FSP has been basically advanced as a grain refinement technique, it is a very attractive process for also fabricating composites. This research aims at fabricating surface composites of SiC/Al2O3 (particulate) on cast aluminum alloys. It will enhance the wear resistance of Al alloy by dispersion of nano-sized particulates on the surface using FSP technique.

Full Text

Reference


Arsenault, R. J., The strengthening of aluminum alloy 6061 by fiber and platelet silicon carbide, Mater. Sci. Eng., 64(2), 171-181(1984).

https://doi.org/10.1016/0025-5416(84)90101-0

Avner, S., Introduction to Physical Metallurgy, 2nd ed., New Delhi: Tata McGraw-Hill, 481-497(1997).

Carey, C., Inderwildi, O. and King, D., Advanced aerospace materials: past, present and future, Aviation and the Environment, 3, 22-27(2009).

Chou, T. W., Kelly, A. and Okura, A., Fibre-reinforced metal-matrix composites, Composites, 16 (3), 187-206(1985).

https://doi.org/10.1016/0010-4361(85)90603-2

Corke, T., Design Of Aircraft, Singapore: Pearson Education Limited, 231-237(2003).

Dave, M. and Kothari, K., Composite material-Aluminium silicon alloy: A review, Paripex-Indian J. Res., 2(3), 148-150(2013).

Iseki, T., Kameda, T. and Maruyama, T., Interfacial reactions between SiC and aluminium during joining, J. Mater. Sci., 19(5), 1692-1698(1984).

https://doi.org/10.1007/BF00563067

Lloyd, D., Lagace, H., Mcleod, A. and Morris, P., Microstructural aspects of aluminium-silicon carbide particulate composites produced by a casting method, Mater. Sci. Eng. A., 107, 73-80(1989).

https://doi.org/10.1016/0921-5093(89)90376-6

Mahendraboopathi, M., Arulshri, K. P. and Iyandurai, N., Evaluation of mechanical properties of aluminium alloy 2024 reinforced with silicon carbide and fly ash hybrid metal matrix composites, Am. J. Appl. Sci., 10(3), 219-229(2013).

https://doi.org/10.3844/ajassp.2013.219.229

Miracle, D. B., Metal matrix composites-From science to technological significance, Compos. Sci. Technol., 65 (15-16),2526-2540(2005).

https://doi.org/10.1016/j.compscitech.2005.05.027

Neelimadevi, C., Mahesh, V. and Selvaraj, N., Mechanical characterization of aluminium silicon carbide composite, Int. J. App. Eng. Res., 1(4), 793-799( 2011).

Prabu, S. B., Karunamoorthy, L., Kathiresan, S. and Mohan, B., Influence of Stirring Speed and Stirring Time on Distribution of Particles in Cast Metal Matrix Composite, J. Mater. Process. Technol., 171(2), 268-273(2006).

https://doi.org/10.1016/j.jmatprotec.2005.06.071

Sarkar, S. and Singh, A., Studies on Aluminum-Iron ore in-situ particulate composite, Open Journal of Composite Materials, 2(1), 22-30, 2012.

https://doi.org/10.4236/ojcm.2012.21004

Starke, K. Jr and Staley, J., Application of modern aluminum alloys to aircraft, Prog. Aerosp. Sci., 32 (2), 131-172(1996).

https://doi.org/10.1016/0376-0421(95)00004-6

Tham, L. M., Gupta, M. and Cheng, L., Effect of limited matrix–reinforcement interfacial reaction on enhancing the mechanical properties of aluminium–silicon carbide composites, Acta Mater., 49(16), 3243-3253(2001).

https://doi.org/10.1016/S1359-6454(01)00221-X

Warren, R. and Andersson, C., Silicon carbide fibres and their potential for use in composite materials, Part II, Composites, 15(2), 101-111(1984).

Contact Us

Powered by

Powered by OJS